minaseizki's memo: 9月 2015

Sun Microsystems Blade 100

職場にあるNVRAMが寿命を迎えた、Sun Microsystems Blade 100で遊んでみます。

Boot

キーボード(Type6/320-1273)と液晶(PLANEX/LCD-8CS)を接続します。
シリアルUSB変換ケーブルを用いて、TearTermで挙動を確認します。
念の為、ネットワークにも接続しておきます。

Speed Jumper is set to 0000.0000.0000.0000
Software Power ON

@(#)OBP 4.16.2 2004/10/04 18:21
CPU SPEED 0x0000.0000.1deb.e980
Initializing Memory Controller
MCR0 0000.0000.56a0.bd04
MCR1 0000.0000.c080.4000
MCR2 0000.0000.0111.000a
MCR3 0000.0000.0000.0086

Clearing E$ Tags  Done
Clearing I/D TLBs Done
Probing Memory Done
Clearing Memory Done
MEM BASE = 0000.0000.0000.0000
MEM SIZE = 0000.0000.1000.0000
MMUs ON
Find dropin, Copying Done, Size 0000.0000.0000.3b50
PC = 0000.01ff.f000.2dc4
PC = 0000.0000.0000.2e08
Find dropin, (copied), Decompressing Done, Size 0000.0000.0005.f3d0
ttya initialized
Reset Control: BXIR:0 BPOR:0 SXIR:0 SPOR:0 POR:1
/: upa at 1f,0 pci
/: upa at 0,0 SUNW,UltraSPARC-IIe (256 KB)
Loading Support Packages: obp-tftp kbd-translator

Loading onboard drivers: ebus
/pci@1f,0/ebus@c: flashprom eeprom idprom
/pci@1f,0: Device 7 isa
/pci@1f,0/isa@7: dma power serial serial
/pci@1f,0/isa@7/dma@0,0: floppy parallel
/pci@1f,0: Device 3 pmu
/pci@1f,0/pmu@3: i2c beep ppm fan-control
/pci@1f,0/pmu@3/i2c@0,0: temperature card-reader dimm-spd
/memory: Probing Memory Bank #0 256 Megabytes
/memory: Probing Memory Bank #1   0 Megabytes
/memory: Probing Memory Bank #2   0 Megabytes
/memory: Probing Memory Bank #3   0 Megabytes
/pci@1f,0: Device c network firewire usb keyboard
/pci@1f,0: Device 8 sound
/pci@1f,0: Device d ide disk cdrom
/pci@1f,0: Device 5 pci
/pci@1f,0/pci@5: Device 0 Nothing there
/pci@1f,0/pci@5: Device 1 Nothing there
/pci@1f,0/pci@5: Device 2 Nothing there
/pci@1f,0: Device 13 SUNW,m64B

NVRAMが切れているので、EthernetAddressとHostIDが異常な値になっています。

Sun Microsystems Type-6とHHK。

NVRAM

中央にある黄色のシールが貼ってあるのが、NVRAM。
MACアドレス等の情報が入っています。

これを輸入した新品のNVRAM(M48T59Y-70PC10)に交換します。
大きさが異なり、緑色のケースに入らないのでケースを使わずに挿入しました。
(向きを間違えないように注意)

無事起動、EthernetAddressが'0:0:0:0:0:0'に変化しました。

Clearing E$ Tags  Done
Clearing I/D TLBs Done
Probing Memory Done
Clearing Memory Done
MEM BASE = 0000.0000.0000.0000
MEM SIZE = 0000.0000.1000.0000
MMUs ON
Find dropin, Copying Done, Size 0000.0000.0000.3b50
PC = 0000.01ff.f000.2dc4
PC = 0000.0000.0000.2e08
Find dropin, (copied), Decompressing Done, Size 0000.0000.0005.f3d0
ttya initialized
Reset Control: BXIR:0 BPOR:0 SXIR:0 SPOR:0 POR:1
/: upa at 1f,0 pci
/: upa at 0,0 SUNW,UltraSPARC-IIe (256 KB)
Loading Support Packages: obp-tftp kbd-translator

Loading onboard drivers: ebus
/pci@1f,0/ebus@c: flashprom eeprom idprom
/pci@1f,0: Device 7 isa
/pci@1f,0/isa@7: dma power serial serial
/pci@1f,0/isa@7/dma@0,0: floppy parallel
/pci@1f,0: Device 3 pmu
/pci@1f,0/pmu@3: i2c beep ppm fan-control
/pci@1f,0/pmu@3/i2c@0,0: temperature card-reader dimm-spd
/memory: Probing Memory Bank #0 256 Megabytes
/memory: Probing Memory Bank #1   0 Megabytes
/memory: Probing Memory Bank #2   0 Megabytes
/memory: Probing Memory Bank #3   0 Megabytes
/pci@1f,0: Device c network firewire usb keyboard
/pci@1f,0: Device 8 sound
/pci@1f,0: Device d ide disk cdrom
/pci@1f,0: Device 5 pci
/pci@1f,0/pci@5: Device 0 Nothing there
/pci@1f,0/pci@5: Device 1 Nothing there
/pci@1f,0/pci@5: Device 2 Nothing there
/pci@1f,0: Device 13 SUNW,m64B


Starting real time clock...
     NOTICE: NVRAM contents invalid; Setting NVRAM parameters to default values.
Setting diag-switch? NVRAM parameter to true
/memory: Probing Memory Bank #0 256 Megabytes
/memory: Probing Memory Bank #1   0 Megabytes
/memory: Probing Memory Bank #2   0 Megabytes
/memory: Probing Memory Bank #3   0 Megabytes
/pci@1f,0: Device c network firewire usb keyboard
/pci@1f,0: Device 8 sound
/pci@1f,0: Device d ide disk cdrom
/pci@1f,0: Device 5 pci
/pci@1f,0/pci@5: Device 0 Nothing there
/pci@1f,0/pci@5: Device 1 Nothing there
/pci@1f,0/pci@5: Device 2 Nothing there
/pci@1f,0: Device 13 SUNW,m64B

ここからはキーボードを外して、TeraTermで作業します。